Warning
This page is located in archive. Go to the latest version of this course pages.

Homework 06 - Panorama

Input Images

Consider the images were captured with the following EXIF info (focal length is in milimeters):

Tag Name Value
0xa002 ExifImageWidth 2400
0xa003 ExifImageHeight 1800
0xa20e FocalPlaneXResolution 2160000/225
0xa20f FocalPlaneYResolution 1611200/168
0xa210 FocalPlaneResolutionUnit inch
0x920a FocalLength 7400/1000

The images were then resized.

07 06 05 04 - reference 03 02 01
bridge_07.jpgbridge_06.jpgbridge_05.jpg bridge_04.jpg bridge_03.jpgbridge_02.jpgbridge_01.jpg

Steps

  1. Manually create 10 image matches (point correspondences) between every pair of adjacent images. Store in the cell matrix u such that u{i,j} are points in the i-th image and u{j,i} are corresponding points in the j-th image. Save in 06_data.mat
  2. Find homographies H_ij for every pair of adjacent images by the same method (optimizing 4 over 10) as in HW-05; use your u2h_optim function for each homography.
  3. Draw 6 histograms of transfer errors of all correspondences into a single image. Use different colour for every histogram, export as 06_histograms.pdf.
  4. Compute homographies H_i4 for every i ∈ <1,7> that maps the images above into the reference image 04 (thus H_44 is identity). Then construct inverse homographies H_4i.
  5. Store all homographies into the cell matrix H, where H{i,j} is the homography from i to j. Save in06_data.mat.
  6. Plot the image borders of the images 02 to 06 transformed to the image plane of the image 04. Export as 06_borders.pdf.
  7. Construct a projective panoramic image from the images 03, 04, and 05, in the image plane of the image 04. Save as 06_panorama.png.
  8. Construct calibration matrix K using the actual image size and the original EXIF. All the images share the same calibration. Store it in 06_data.mat
  9. Establish a transformation between each image plane and the coordinate system of the cylinder, described below.
  10. Plot the image borders of all the images mapped onto the cylinder (06_borders_c.pdf).
  11. Construct a panoramic image from all the images mapped onto the cylinder (06_panorama_c.png).
  12. Optionally, construct a cylindrical panorama from a set of your images (total pan at least 180 degrees) (06_panorama_c_own.png). Credited by at most 2 bonus points. In this case submit the input images as well (06_image01.jpg, etc ).
Example of histogram of errors
Example of image borders (origin not shifted)
Example of projective panorama (images 3-4-5)
Example of cylindrical panorama (all images)

The cylinder

The cylinder is defined in the coordinate system γ (blue) of the image 04 (green) such that:

  • cylinder axis is equal to c2 axis of γ,
  • image plane of the image 04 is tangential to the cylinder,
  • image coordinate system defined on the cylinder surface has square pixels and equal horizontal resolution in the line where it touches the image 04.

This leads that the cylinder has radius = 1 in the γ system. The cylinder surface is a set of points <latex>[x_{\gamma} y_{\gamma} z_{\gamma}]^\top</latex> such that

<latex>x_{\gamma}^2 + z_{\gamma}^2 = 1</latex>

For parametrisation of the cylinder surface we define two coordinate systems: the first (magenta) is based on γ, second (red) is pixel-based system of panoramic image.

First, the surface of the cylinder is parametrised by circumference length (equal to angle since radius=1) and by the <latex>y_{\gamma}</latex> coordinate. The ray <latex>\lambda [x_{\gamma} y_{\gamma} z_{\gamma}]^\top</latex> intersects the cylinder in the point

<latex>\lambda=\frac{1}{\sqrt{x_{\gamma}^2 + z_{\gamma}^2}}</latex>

<latex>[ a_{c\gamma}; y_{c\gamma} ] = [ \mbox{the angle given by } x_{\gamma} \mbox{ and } z_{\gamma}; \frac{y_{\gamma}}{\sqrt{x_{\gamma}^2 + z_{\gamma}^2}} ]</latex>

Second, the pixel size must be applied and image origin adjusted. Since the horizontal pixel size is 1/K(1,1) measured in units given by γ system, this leads to

<latex>[ x_c; y_c ] = K_{11} [ a_{c\gamma}; y_{c\gamma} ] + [x_{0c}; y_{0c} ]</latex>

where the origin <latex>[x_{0c}; y_{0c}]</latex> must be found such that all pixels from the input images will fit into the resulting panorama.

Upload

Upload an archive consisting of:

  1. 06_data.mat
  2. 06_histograms.pdf
  3. 06_borders.pdf
  4. 06_panorama.png
  5. 06_borders_c.pdf
  6. 06_panorama_c.png
  7. your own images and panorama, if created
  8. hw06.m – your Matlab implementation entry point.

any other files required by hw07.m (including data and files from the repository).

courses/gvg/labs/gvg-2017-hw-06.txt · Last modified: 2019/01/19 18:22 (external edit)